T h e L o n e r M6 S a fe ty S yste m CONTENTS A b o u t t h e - PowerPoint PPT Presentation

T h e L o n e r M6 S a fe ty S yste m

CONTENTS A b o u t t h e d e v i c e S t a r t i n g y o u r s h i f t D u r i n g y o u r s h i f t G e n e r a t i n g M a n u a l A l e r t s R e c e i v i n g a v o i c e c a l l E n d i n g y o u r s h i f t Q u e s t i o n s ?

ABOUT THE DEVICE

ABOUT THE DEVICE There are three primary mechanical components of the Loner device. Belt Clip SureSafe monitoring light and power button Latch

STARTING YOUR SHIFT

STARTING YOUR SHIFT TURNING ON YOUR LONER Press the power button The green SureSafe light will blink until it is connected to the Blackline Safety Network. Once connected, the light will be SOLID GREEN. This means your safety is now monitored.

STARTING YOUR SHIFT WEARING YOUR LONER Clip the device to the side of your hip or to your chest pocket

STARTING YOUR SHIFT Do not leave Loner unattended when powered on This can lead to false alerts

DURING YOUR SHIFT

DURING YOUR SHIFT AUTOMATIC FEATURES During your shift, the device may ask you to confirm that you are OK when it detects one of the following: Fall detection No-motion Check-in

DURING YOUR SHIFT AUTOMATIC FEATURES – IF YOU’RE OK No-motion Fall Detection Check-in Pending Alarm This returns Loner to If you’re OK press normal function. the confirm button No notification is on the latch sent.

DURING YOUR SHIFT AUTOMATIC FEATURES – IF YOU CAN’T CONFIRM No-motion Fall Detection Check-in If you can’t press the confirm Pending Alarm button after a certain period of time, the device will go into high alarm Once an alert is acknowledged The high alarm can be silenced by This sends an by monitoring personnel, the pressing and holding the button. The alert notification loner will display a blue light alert notification still remains active.

DURING YOUR SHIFT PRE CHECK-IN Check-in timer reset Before pre-check in 00:54:34 2:00:00 To do this, press and hold the latch for two vibrations. This will reset the check-in timer before the automatic alarm sounds. Your device will automatically check you in if you are driving over 35 km/h.

DURING YOUR SHIFT MANUAL FEATURES During your shift, you may need to request help using one of the manual features: Emergency alert Silent alert (Audible)

DURING YOUR SHIFT Emergency alert Request help by An alert The high alarm can Once an alert is pulling down the notification will be silenced by acknowledged by latch be sent to pressing and holding monitoring monitoring the button. The alert personnel, the loner personnel notification still will display a blue remains active. light

DURING YOUR SHIFT Silent Alert (No audible or visual alarm is generated on the Loner device) An alert No alert acknowledged blue light Press the confirm button notification will will be displayed on the device during a silent until the vibration stops be sent to alert even if monitoring personnel have (two full vibration pulses ~5 sec.) monitoring acknowledged the incident personnel

RECEIVING A VOICE CALL

RECEIVING A VOICE CALL RECEIVING A VOICE CALL That was a This is the safety false alarm. I *BEEP* monitoring center. do not require We had an alert assistance. from your device. Understood. I will go ahead and resolve your alert. *BEEP* A voice call can be made by monitoring personnel Once the call is connected you can speak back directly to the device. After an alert is triggered and forth to monitoring personnel. When the call the device will beep once when a call is has ended the device will beep once more. connected.

RECEIVING A VOICE CALL RECEIVING A VOICE CALL – AFTER A SILENT ALERT … When a silent alert is generated, monitoring personnel can still connect with the Loner device. However the Loner will not beep and it will be in a ‘listen only’ mode.

NOTIFICATIONS

NOTIFICATIONS Link lost alarm Low battery alarm Your Loner will notify you if it loses Your Loner device is configured to signal to you cellular communication. when the battery falls below a certain configured percentage SureSafe monitoring light BLINKING Low battery alarm is Your Loner SureSafe light will begin blinking to characterized by a short beep confirm that your safety is not being monitored. and a quick flash every 5 If configured, the device may initiate a link lost minutes. Charge your device as alarm. soon as possible.

ENDING YOUR SHIFT

ENDING YOUR SHIFT TURNING OFF YOUR LONER DEVICE Press the power button until beeping and vibration stops (usually 3 seconds) The device will begin its shutdown sequence and the SureSafe light will flash and then turn off once your Loner logs off from the Blackline Safety Network. Your safety is no longer being monitored

ENDING YOUR SHIFT CHARGING YOUR LONER Full charge takes approx 4 hours Battery Life is 20 hours While the device is Insert the charger into the When Loner is charging the red lights on bottom of the device and charged, the red the base will flash connect to power source lights will turn on continuously.

QUESTIONS?

F o r mo re su p p o rt ma te ri a l s, P l ease vi si t s u p p o rt.b l a c k l i n e s a fe ty.c o m C us tomer C are: 1 -8 7 7 -8 6 9 -7 2 1 2 0 0 4 5 / R 4 / 2 0 1 6 - 0 6 - 0 1